Skip to content
Wish lists
Wish lists
Cart
1 item

Keep Truckin’ Blog

6 Pin Trailer Wiring: Pinout, Colors and Testing Guide

by Frank A. 08 Nov 2026 0 comments

A 6-pin (6-way) round trailer connector carries six circuits: ground, tail/running lights, left turn and brake, right turn and brake, electric trailer brakes, and 12-volt auxiliary power. The common color code is white for ground, brown for running lights, yellow for left turn, green for right turn, blue for brakes and black or red for 12V auxiliary. Colors are a convention, though, so you confirm every pin with a multimeter before you connect anything. This guide shows the pinout, how to read the diagram, how to wire a replacement plug and how to troubleshoot it.

Allstartruckparts
Keep Trailer Wiring Dependable
Explore truck and trailer wiring, lighting, and safety products designed for demanding conditions and dependable visibility.

TL;DR

  • A 6-way plug does everything a 4-way flat does (ground, running lights, left and right turn/brake) and adds an electric brake line and a 12V auxiliary line.
  • Typical colors: white ground, brown running lights, yellow left, green right, blue brakes, black or red 12V auxiliary.
  • Plug brands label terminals differently and the blue and black/red pair is the one most often swapped, so test each wire’s function before you crimp.
  • Most “nothing works” and “dim lights” problems trace back to the ground, the fuse or a loose connector.
  • Use color-coded 6-conductor wire so the colors in the cable match the plug you are wiring.

Table of Contents

What a 6-way connector does

Think of the 6-way as a 4-way flat with two extra jobs. A 4-way flat covers ground, tail lights, left turn and right turn. That is enough for small utility and boat trailers with no electric brakes. The 6-round adds a line for electric trailer brakes and a line for 12-volt auxiliary power or battery charging. With it you can run a brake controller and keep a trailer battery topped up while you drive.

You will see 6-way plugs most often on horse trailers, stock trailers and utility trailers, and on gooseneck trailers. The center terminal is an auxiliary terminal. Depending on the trailer, it feeds either backup lights or a 12-volt positive wire. Because there are several possible combinations for those two extra circuits, the same plug can be wired differently from one trailer to the next. That is why the testing steps below matter more than any single chart.

Plug Circuits Typical use
4-way flat Ground, running, left turn, right turn Small utility and boat trailers without electric brakes
6-way round The four above, plus electric brakes and 12V auxiliary Horse, stock and utility trailers, gooseneck trailers
7-way The six above with a dedicated reverse or accessory circuit, depending on the standard used Larger trailers and RVs

If your trailer has a 7-way plug instead, our guide to wiring a 7 pin trailer harness covers that pinout.

The 6-way pinout and wire colors

Here is the function and color of each pin as most diagrams show it. This follows the common color code published for the 6-way connector:

Function Common color What it does
Ground White Returns current to the tow vehicle
Tail / running lights Brown Tail, marker and clearance lights
Left turn / brake Yellow Left stop and turn signal
Right turn / brake Green Right stop and turn signal
Electric brakes Blue Output from the brake controller to the trailer brake magnets
12V auxiliary Black (sometimes red) Constant 12V for a trailer battery, interior lights or a winch

The ASME-style color code for the 6-way connector assigns white to ground, brown to running lights, yellow to left turn and brake, blue to the brake control, green to right turn and brake, and black to auxiliary power. Some older or imported plugs use red for the auxiliary wire and black for ground, so a trailer wired to one chart can look wrong against another.

We cover the broader color question in our trailer plug wiring colors guide, including the mistakes we see most.

How to read a 6-way trailer wiring diagram

Most wiring mistakes start with looking at the diagram from the wrong side. A plug has a face (where the pins or sockets meet the mating plug) and a back (where wires enter). Diagrams drawn from one side are the mirror of diagrams drawn from the other. Before you trust a drawing, find the note that says which side it shows.

One published guide looking at the plug face describes the layout as a clock: brown at 12 o’clock, yellow at 10, green at 2, white at 6, blue at 8 and red or black at 4. Another diagram lists positions differently, with yellow at 9 o’clock, green at 3, blue at 7 and black at 5. Both can be right, because they are drawn from different viewpoints or for different plug styles. Treat clock positions as a starting point, not a rule.

Three habits keep you out of trouble:

  1. Identify the view (face or wire side) on every diagram you use.
  2. Use the tow vehicle’s socket and the trailer’s plug as a pair, and confirm that each pin you wire on one side lands on the same function on the other.
  3. Write down the pin-to-function map from the old plug before you cut it off.

If you want a one-page reference for the whole family, our trailer light wiring diagram guide shows 4 through 7 pin pinouts side by side.

Why you should verify colors before you wire

Wire color is a clue, not proof of function. Colors are a convention rather than a law. Terminal labels differ between plug brands even when the functions match, and the electric-brake and 12V auxiliary pair is the one most commonly swapped, especially on horse trailers.

The stakes are real. One guide warns that connecting constant 12V power to the brake circuit can make trailer brakes lock up or wear prematurely. Connecting the brake signal to an auxiliary circuit leaves the electric brakes dead. Either way you find out on the road, which is the worst place to learn it.

When you replace a plug, match positions from the old plug to the new one, or test for function so the connector ends up wired to the standard code. Color suggestions from a manufacturer are not a promise of what you will find in the wire.

Why you should verify colors before you wire

Wiring a replacement 6-way plug, step by step

This is the process we recommend for a replacement trailer-side plug or a new run of cable. Work with the trailer unplugged from the truck.

  1. Map the old plug. Photograph it from the wire side, then note which color goes to which terminal. Trace any wire that does not match the chart.
  2. Identify each function with a meter. At the tow vehicle socket, set the multimeter to DC volts. With the truck running its lights and the brake controller set to apply the brakes manually, find the pins that carry running, left, right, brake output and constant 12V. This tells you what the trailer wires must do.
  3. Cut back clean copper. Strip about a quarter inch of insulation. If the end is green or corroded, cut back until the strands are bright.
  4. Terminate to the labeled terminals. Most plugs mark the terminals with letters or a color key. Use those marks instead of guessing from cavity position.
  5. Ground first. Make the white ground connection solid, and attach the trailer ground to bare metal on the frame. A poor ground is a classic cause of dim or flickering lights.
  6. Seal and strain-relieve. Use a connector body that clamps the cable jacket so pulling on the cord never loads the terminals. Add dielectric grease in wet climates.
  7. Test before towing. Plug into the truck and run the full check: running lights, left and right turn, brakes, and the aux circuit if you use it.

For long runs between the plug and the lights, the cable matters as much as the plug. A color-coded 6-conductor cable keeps the wires you see at the plug matching the circuits you planned. Our 6 way trailer wire, 14 AWG CCA, 6 conductor comes color-coded and is listed in 25, 50 and 100 ft lengths.

Testing a 6-way connection with a multimeter

A simple meter is all you need. One step-by-step guide says to set the meter to the 20V DC range, put the black probe on the trailer’s ground pin and probe the other pins while the vehicle lights are on. Work through the plug in this order:

  • Ground. Check continuity or low resistance between the ground pin and the trailer frame. The same guide treats a good ground as below 0.5 ohms.
  • Running lights. Turn on the truck’s headlights. The brown pin should show about battery voltage.
  • Left and right. Operate the turn signal and then the brake pedal. Yellow and green should each pulse with the signal and stay steady on the brake.
  • Brakes. Apply the trailer brakes with the controller’s manual lever. The blue pin should show a controlled output that rises as you increase the setting.
  • Auxiliary. The black (or red) pin should read battery voltage with the ignition on, independent of lights or brakes.

Ground deserves special attention. The same testing guide puts around 90% of trailer issues down to poor grounding rather than broken power wires. Without a clean path back to the battery, lights glow dimly or blink out of sync. If you see odd behavior, such as the left signal flashing the right lamp, check the ground before you rewire anything.

Troubleshooting: lights, brakes and auxiliary power

Nothing works at all

Start with the truck side. One troubleshooting guide suggests you check the truck’s trailer-circuit fuse, confirm the connector is fully seated, test for 12V at the truck connector pins and check ground at both truck and trailer. If the fuse is blown repeatedly, look for a pinched wire or a shorted lamp. Our guide on trailer light fuse size explains what rating makes sense for LED loads.

Lights work but the brakes do not

The checks here are whether the brake controller has power and shows the trailer as connected, whether the blue wire has continuity, whether the breakaway switch is in the run position, and the resistance of the brake magnets. The same guide gives 3 to 4 ohms per magnet as the expected range. If the blue wire tests fine at the truck but is dead at the trailer, look for a break in the cable or a corroded terminal in the plug.

No auxiliary power

Check the inline fuse near the truck battery, test for voltage at the truck connector, confirm continuity on the black or red wire, and check the trailer-side fuse or breaker. That guide also recommends a 30-amp inline fuse on the 12V auxiliary wire near the battery, and notes that a short in this circuit can drain the truck battery overnight or start a fire. Fuse the circuit at the source and keep the wire away from sharp edges and heat.

Lights flicker, dim or turn signals are reversed

Common installation errors include an inadequate ground causing dim or flickering lights, reversed turn signals from swapping the yellow and green wires, poor terminal connections and incorrect wire gauge. Reflash the ground, then check the yellow and green at the plug. For roadside diagnosis of lights that quit mid-trip, our guide to fixing trailer lights roadside walks through isolating the circuit, the ground and the connector in order.

Choosing wire and lights that hold up

A wiring job is only as good as its weakest point, and on trailers that is usually moisture. Water gets in at splices, at the plug and behind lamp housings, then corrodes copper and raises resistance. Some habits that help:

  • Run one continuous cable from the plug toward the junction box where you can, instead of stacking splices. If you use a junction box, our trailer junction box wiring guide shows how to diagram it first and test with a meter.
  • Use sealed lamps and grommets where wires pass through metal so the jacket never rubs on a sharp edge.
  • Match the cable to the circuit. Brakes and auxiliary power carry more current than a marker light, so route them on a conductor sized for the load and the length of the run.
  • If you are adding backup lights, see our guide to trailer reverse lights for the wiring and DOT-compliant kits.

Our perspective

We hear the same thing from fleet techs and owners again and again: the plug is rarely the problem, the wire behind it is. A 6-way connection is only as dependable as the ground, the terminations and the cable that carries the current, and those get the least attention at purchase time.

That is why we build our catalog around the whole circuit and not just the lamp. Our lighting is designed with leak-proof housings and high-intensity reflectors meant to exceed federal standards. Our wiring uses thicker copper construction and color-coded conductors, designed to hold up on long hauls and in harsh weather. When the cable, grommets, plugs and lights come from one source and share one standard, there are fewer mismatched colors and fewer surprises at the roadside.

Our advice for any 6-way job is the same: map the plug, test every function, ground it well and fuse the auxiliary line. Do those four things with sound parts and the trailer will be quiet and predictable for years.

All

Get the parts for your 6-way wiring job

If you are rewiring a trailer, start with the cable. Our 6 way trailer wire is a 14 AWG, 6-conductor, color-coded cable that we describe as DOT and SAE approved, made for trailers, campers and tow rigs. If your trailer uses a 5-conductor run, there is a 5 way version too.

6 Way Trailer Wire Heavy Duty 14 AWG/Gauge CCA 6 Conductor Wire RV Trailer Tow Campers Cable Cord Insulated Stranded Copper Clad Aluminum Conductor Flexible Color-Coded DOT SAE Approved 25/50/100 FT

For lights, grommets, plugs and reflective tape to go with it, browse the full range of DOT-compliant trailer lighting and wiring.

FAQ

What is the difference between a 4-way and a 6-way trailer plug?

A 4-way flat plug carries ground, running lights, left turn and right turn. A 6-way adds a circuit for electric trailer brakes and a circuit for 12V auxiliary power. That makes it the right fit when the trailer has electric brakes, a battery to charge or interior lights.

What color wire goes to which pin on a 6-way plug?

The common code is white for ground, brown for running lights, yellow for left turn and brake, green for right turn and brake, blue for electric brakes and black or red for 12V auxiliary. Plug brands label terminals differently, so check the markings on your own plug and test each function with a meter before you connect.

Can the blue and black wires be swapped?

They can be, and that is a known source of trouble. Some applications reverse the positions normally associated with the black battery-power wire and the blue brake-output wire, so a position copied from the wrong diagram can put constant power on the brake circuit. Confirm which wire is the brake output with the controller active, and which is constant 12V with the ignition on.

Why do my trailer lights flicker or look dim?

In most cases the ground is poor. Clean the contact point to bare metal on the frame, tighten the connection and check that the white wire reads low resistance to the plug’s ground pin. After that, look for corroded terminals and a plug that is not fully seated.

Do I need a fuse on the auxiliary wire?

Yes. The auxiliary line is constant power from the truck battery, so it needs protection near the source. One guide recommends a 30-amp inline fuse near the battery, because a short can drain the battery or start a fire. Size the fuse to the wire and the load, and keep the run protected from abrasion.

Sources

Sample Image Gallery

SPRING SUMMER LOOKBOOK

Sample Block Quote

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis.

Sample Paragraph Text

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis nec danos dui. Cras suscipit quam et turpis eleifend vitae malesuada magna congue. Damus id ullamcorper neque. Sed vitae mi a mi pretium aliquet ac sed elitos. Pellentesque nulla eros accumsan quis justo at tincidunt lobortis deli denimes, suspendisse vestibulum lectus in lectus volutpate.
Prev post
Next post

Leave a comment

Please note, comments need to be approved before they are published.

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Edit option
Back In Stock Notification

Choose options

this is just a warning
Login
Your Cart Good Picks!
Free shipping in all us ORders