Skip to content
Wish lists
Wish lists
Cart
0 items

Keep Truckin’ Blog

Why Marker Lights Flash With the Turn Signals

by Frank A. 20 Nov 2026 0 comments

Marker lights that blink with the turn signal are either doing what federal rules allow or showing a wiring fault, and you can tell which in a few minutes. Side markers that flash together with the turn signal on the same side are permitted. Markers that flash on the wrong side, flash alternately in a way you did not wire, or flicker with the turn signal off usually point to a bad ground, a corroded connector or a shared-circuit problem. At All Star Truck Parts we sell DOT-compliant marker lights, wiring, connectors and grommets, so this guide covers both the rule and the repair.

Allstartruckparts
Restore Reliable Marker Light Visibility
Find DOT-compliant marker lights, wiring, connectors, and grommets designed for demanding conditions and dependable visibility.
Visit

TL;DR

  • Federal regulators allow a side marker to flash in step with the turn signal on the same side and end of the vehicle. Flashing on the opposite side is a fault.
  • A combination mid-ship turn signal and side marker lamp is built to flash. A standalone marker that blinks usually points to a ground or splice problem.
  • Most trailer cases trace back to the trailer connector, a loose lamp connection or a corroded frame ground. Check those first.
  • Use a multimeter with the power locked out: voltage drop above roughly 0.1 to 0.2 V across a connector means excess resistance.
  • Repair with sealed connectors and fresh DOT-compliant lamps so the fix lasts through weather and inspections.

Table of Contents

Is it normal for marker lights to flash with the turn signal?

Sometimes, yes. The federal lighting standard, FMVSS No. 108, treats the two lamp types as separate functions. Side marker lamps are mounted on the permanent structure near the front and rear edges to show the vehicle’s overall length. The turn signal is the signaling element that flashes on the side of the intended turn.

The rule does let the two overlap. In a 1976 interpretation, NHTSA said that a side marker may flash for signaling purposes and that it saw no problem with a required side marker flashing simultaneously with the required turn signal on the same side and end. It also said that a system making the markers flash alternately with the turn signal detracts from the signal’s value. A later NHTSA letter confirms that side markers may flash with the turn signals, and that on trailers the lamps must be amber forward of the midpoint and red to the rear.

So the first question is simple: which lamp blinks, and on which side?

What you see Likely meaning
Amber front marker flashes with the turn signal on the same side Normal. Allowed by design
Mid-ship amber lamp flashes with the turn signal on its side Normal if it is a combination turn signal and marker lamp
Markers on both sides flash when you signal one way Fault. Look at grounds and shared wiring
Markers flicker with the turn signal off Fault, or a trailer connection check on some towing systems
Rear red markers pulse with the brake or signal Fault. Look at the ground path

Markers versus turn signals: what each one is for

A marker lamp is a presence light. NHTSA’s research on side markers explains that they were required so a driver approaching at an angle at night can see a vehicle early enough to slow or stop. The study notes that front lamps are amber, rear lamps are red, they sit at least 15 inches above the ground, and vehicles over 30 feet long carry extra amber lamps at the midpoint. The lamps are lit whenever the parking lights are on.

A turn signal is an intent light. It is meant to flash, and its whole value comes from being a different signal from the steady lamps around it. That is why the rule worries about markers flashing out of step with it. If you want the color logic for your own build, our guide to amber versus red markers shows which goes where on trucks and trailers.

Seeing a long trailer’s position at night also depends on what the other driver is looking through, and night visibility through tinted glass is a reminder of why a bright, steady marker line matters.

1. The lamp is a combination lamp

Some lamps do both jobs. A mid-ship lamp on a long trailer can be a turn signal and a side marker in one housing. It glows steadily with the running lights and flashes with the turn signal. For commercial vehicles, 49 CFR 393.25(e) requires exterior lamps to be steady-burning except for turn signals, hazard flashers and a short list of warning lamps. It also says a lamp that shares a shell or housing with a turn signal need not be steady-burning while the signal is in use.

If you want this behavior on purpose, buy a lamp designed for it. Our 6 inch oval mid-ship turn signal and side marker lights are 24-LED amber lamps with a 3-wire pigtail and a weathertight plug.

2Pcs 6 Inch Oval 24 LED Mid Ship Turn Signal and Side Marker Clearance Lights Amber Lens Halo Surface Mounted Sealed with 3-Wire Pigtail for Led Trailer Lights, Weathertight Plug

2. A supplemental lamp follows a flashing lamp

NHTSA’s April 2025 interpretation says all auxiliary lamps must be steady-burning, with one exception: auxiliary lamps that supplement required flashing lamps, such as turn signals. A supplemental side lamp can therefore flash with the turn signal. A supplemental lamp that flashes on its own, or with something other than a turn signal, does not fit that exception.

3. A wiring fault is sending the signal where it should not go

This is the case that brings most people to the search box. The marker circuit and the turn circuit share a return path, usually a ground. When the ground is poor, current looks for another way home. It can flow backward through a marker circuit, so the markers pulse with the signal. On trailers the weak points are well known. A May 2022 service bulletin lists loose or broken trailer-connector connections, loose lamp-assembly connections and corroded frame grounds as common causes of intermittent or inoperative trailer lamps. It also warns that wire nuts are not sealed for automotive use.

The same bulletin has one more point for late-model towing vehicles. With a trailer connected and the ignition off, the trailer lighting control module can pulse the lighting circuits to check the connection. That flicker is a normal condition on that system, not a failed lamp.

How to find the fault, step by step

The method below follows the heavy-truck lighting diagnosis in VoTechWorks’ lighting lesson, adapted to a flashing-marker complaint. You need a digital multimeter, a wiring diagram for the vehicle or trailer, and basic hand tools.

Six steps for diagnosing flashing trailer marker lights

Before you start

The same lesson calls for lockout and tagout: disconnect the trailer power cord and lock the tractor battery disconnect. Wear safety glasses, chock the wheels before working under the vehicle, and use insulated probes rated for the voltage. A short in a high-amperage lighting circuit can start a wiring fire.

Step 1: Note exactly what flashes

Write down which lamps flash, with which function (left signal, right signal, brake, hazards) and with the headlights or running lights on or off. Markers flashing on both sides when you signal one way point to the shared return. A single lamp flashing points to that lamp’s own connection or its ground.

Step 2: Inspect the connector and plugs

The seven-way trailer plug is the first place to look. Check for green or white corrosion, bent pins and loose wires. Water in the connector is a common cause of flickering. Replace a damaged plug instead of cleaning it again and again. We sell connectors, grommets and plugs alongside copper and copper-clad wiring, so a worn connection can be rebuilt with matched parts.

Step 3: Check the frame ground

Follow the white ground wire to the frame and look for rust, paint under the ring terminal, or a loose bolt. Clean it to bare metal and re-secure it. On a trailer built with several marker lamps, a poor ground at one point can make every lamp on the circuit misbehave.

Step 4: Check power and run a voltage-drop test

Verify power at the fuse, then test across each connector while the circuit is loaded. The lesson says that more than 0.1 to 0.2 V across a connector shows excessive resistance. That resistance is what makes the current take the wrong path. Work the circuit in halves: if the reading is good at the middle, the fault is toward the end of the run.

Step 5: Test continuity with the power off

Once the circuit is de-energized and locked out, test continuity on the suspect wire and on the ground path. A wire that reads open or high needs replacing. Do not splice with wire nuts. Wire thickness matters too: undersized or low-grade conductors run hotter and drop more voltage over a long trailer, which is why we build our wiring with thicker copper.

Step 6: Repair, seal and verify

Use heat-shrink butt connectors and dielectric grease, as the lesson prescribes, then retest every function. Where a lamp’s housing or grommet has failed, replace it. Water that gets in through a cracked lens or a missing grommet corrodes the contacts and brings the problem back. Our trailer marker lights use sealed IP67 waterproof construction with grommet mounting, and a flush-mount grommet and plug keep the wiring entry tight.

What about LED replacement lamps?

A lamp swap sometimes starts the complaint, as one reader found when LED bulbs in the side markers began to blink after replacement. Marker circuits are often shared with other functions, and a lamp with a different current draw can reveal a weak ground that the old bulb hid. Check the ground first. Then fit a lamp designed for the position instead of a generic bulb: a complete sealed LED marker lamp with its own pigtail is easier to make weatherproof than a bulb in an old socket.

For trailers, our 2 inch round 7 LED clearance and marker lights are DOT FMVSS 108 and SAE P2 rated, with a reflector lens and grommet. The 2 inch round 9 LED amber and red set adds a plug.

What the rules require so the fix stays compliant

A repair is also a compliance check. Here is what applies when you touch marker wiring.

  • Trailer layout. FMVSS 108 calls for two amber side markers as far forward as practicable and two red ones as far rearward as practicable. Trailers over 30 feet also need amber intermediate side markers and reflex reflectors near the midpoint.
  • Commercial trailers. 49 CFR Part 393 Subpart B lists rear side-marker lamps for semitrailers and full trailers 80 inches or more wide, at a height of at least 15 inches on trailers built on or after March 1, 1979.
  • Steady-burning. Outside turn signals, hazards and a short list of warning lamps, commercial vehicle lamps must burn steadily. A marker that flashes on its own can be cited.
  • State rules. California Vehicle Code 24252(b) requires at least 85 percent of the bulb’s design voltage at a side marker or clearance lamp socket with the engine running. The statute also limits combining a turn signal with a stoplamp. It is a useful target for voltage drop even outside California.

For a fleet walk-around, our DOT lighting inspection checklist covers the lamps an inspector looks at. Our guides on the 80 inch and 30 foot marker rules and clearance versus marker lights help when you decide which lamps a build needs.

Replacing marker lights that keep failing

If a lamp has failed, pulse after pulse of moisture is usually the reason. Our lighting is designed with leak-proof housings and bright LEDs for harsh weather. For a full trailer refresh, the 10-pack of amber 2 inch round 9 LED marker lights covers a long trailer in one order. For the rear, the red 3-light 24 LED ID bar is a ready-made identification bar. Fleet buyers, trailer builders and installers can browse lighting, wiring, reflective products and grommets at All Star Truck Parts.

RED 3 LIGHT COMBINATION CLEARANCE ID BAR MARKER 24 LED TRAILER IDENTIFICATION

Our view: fix the circuit, then fit the right lamp

Most blinking-marker calls come down to the same pattern: a shared ground, a tired connector, and a lamp that was never sealed against water. Swapping lamps without fixing the return path hides the problem for a week.

We build our lighting for trailers that run long hauls in rain, road salt and heat. That means leak-proof housings, bright LEDs, DOT-compliant construction and thicker copper wiring. A good lamp on a poor connection still flickers, so we sell the wiring, connectors, grommets and plugs that complete the circuit, not just the lamp at the end of it.

Choose a combination lamp when you want a marker that flashes with the turn signal. Choose a steady marker when you do not. Then wire each one to a clean ground.

All

FAQ

They may, but they do not have to. NHTSA has said a side marker can flash simultaneously with the turn signal on the same side and end of the vehicle. Flashing alternately with the signal, or on the opposite side, is not what the rule had in mind.

Are side marker lights the same as turn signal lights?

No. Under FMVSS 108, a side marker shows the vehicle’s length and position and stays lit with the parking lights. A turn signal flashes to show an intended turn. A combination lamp can do both in one housing.

The usual causes are a corroded or loose trailer connector, a loose lamp connection or a poor frame ground. Water intrusion makes each of them worse. On some late-model tow vehicles, a trailer module also pulses the lighting circuits to check the connection, which can look like flicker.

Do side marker lights have to work?

On trailers 80 inches or wider, federal commercial vehicle rules require side marker lamps, and on trailers over 30 feet long they also require intermediate amber lamps. A dead or misbehaving marker is a lighting defect, so repair it before your next inspection.

Sources

Sample Image Gallery

SPRING SUMMER LOOKBOOK

Sample Block Quote

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis.

Sample Paragraph Text

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis nec danos dui. Cras suscipit quam et turpis eleifend vitae malesuada magna congue. Damus id ullamcorper neque. Sed vitae mi a mi pretium aliquet ac sed elitos. Pellentesque nulla eros accumsan quis justo at tincidunt lobortis deli denimes, suspendisse vestibulum lectus in lectus volutpate.
Prev post
Next post

Leave a comment

Please note, comments need to be approved before they are published.

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Edit option
Back In Stock Notification

Choose options

this is just a warning
Login
Your Cart Good Picks!
Free shipping in all us ORders