Trailer Light Color Rules: What Must Be Red, Amber or White
The short version: on a U.S. trailer, lamps and reflectors at the rear must be red, those at the front or on the side near the front must be amber, and the license plate lamp must be white. Rear turn signals are the one place you get a choice, red or amber. Everything else is about putting the right color in the right position, and not adding lights that blur those signals.
This guide covers commercial trailers first, because that is where federal rules apply most directly, then shows where state rules differ and what to do about decorative or add-on lighting.
TL;DR
- Rear stop, tail, rear side-marker lamps and rear reflectors: red. License plate lamp: white.
- Front and near-front side lamps and turn signals: amber. Rear turn signals: red or amber.
- Color is tied to position. An amber lamp at the back (other than a turn signal) or a red lamp at the front is a violation.
- Extra lights on a trailer rear or a sleeper can be an issue if their color or location confuses the required lamps. State codes add their own wording.
- Wire colors on trailer plugs are an industry convention, not a lighting law. Test every circuit instead of trusting the colors.
Table of Contents
- The federal rule in one table
- Rear lights: stop, tail and turn
- Side markers, clearance lamps and reflectors
- License plate lamp
- Federal rules versus state rules
- Add-on lights, glow lighting and sleeper accents
- Wiring colors: convention, not law
- Quick compliance check before you roll
- Perspective
- Lighting built for the right position
- FAQ
- Sources
The federal rule in one table
For commercial motor vehicles, trailer lamp and reflector colors and mounting are set out in 49 CFR 393.11 and the related Subpart B lamp rules. The equipment standard behind the hardware itself is FMVSS No. 108, which NHTSA enforces on manufacturers. Put together, the color picture looks like this:
| Lamp or device | Required color | Where it goes |
|---|---|---|
| Tail lamps | Red | Rear, one each side |
| Stop lamps | Red | Rear, one each side |
| Rear turn signals | Red or amber | Rear, one each side |
| Rear side-marker lamps | Red | Side, near the rear |
| Rear reflex reflectors | Red | Rear, one each side |
| Front and near-front side lamps | Amber | Side, near the front |
| License plate lamp | White | Rear, lighting the plate |
The federal text states it plainly: lamps at the front or on the side near the front are amber, lamps at the rear or on the side near the rear are red, and the license plate lamp is white. Intermediate side markers on longer trailers are amber, which is the detail drivers most often forget.
Why the colors follow position
Other drivers read your trailer in a fraction of a second at night. Amber says front or midpoint, red says back. NHTSA’s own interpretations explain that familiar lighting schemes improve highway safety because drivers recognize what a light means and react fast. That is why a lamp in the wrong color is a defect even if it is bright and works perfectly.
NHTSA has also confirmed the basic split for trucks and trailers: front side markers and turn signals must be amber, rear side markers red, and rear turn signals red or amber. Using another color for those functions does not meet FMVSS No. 108.

Rear lights: stop, tail and turn
Tail and stop lamps on a trailer are red. They sit on the rear, symmetrically either side of the vertical centerline and as far apart as practicable. The federal rule puts them at roughly 15 to 72 inches above the road, per the same Subpart B lamp requirements.
Red or amber turn signals
Rear turn signals may be either color on commercial vehicles. Many states say the same in their own codes. Ohio’s rule, for example, says stop lamps must be red and rear-facing turn signals may be red or amber. Texas goes a step further in its statute: a device or reflector mounted on a vehicle’s rear must be or reflect red, and a rear signaling device may be red, amber or yellow.
Practical takeaway: if you run a combined stop/turn/tail lamp, red on the whole lens is the safest choice across states. If you run a separate turn lamp, amber is easy to recognize and legal. Mixing is fine, as long as each function is in a permitted color and each side matches the other.
One lamp, three jobs
Combination lamps are the norm on trailers. A single red lens with separate LED circuits for tail, stop and turn can satisfy all three functions if it carries the right certification. Look for DOT and SAE markings on the lens itself. Texas DPS notes that colored bulbs must carry a DOT or appropriate SAE stamp, and that tinted bulbs do not make a legal lamp, so a red-coated bulb inside a clear lens is not a substitute for a lens made to be red.
Side markers, clearance lamps and reflectors
This is where most roadside citations on trailers come from, and it is mostly a color-and-position story.
- Rear side markers: red, on the side near the rear. Trailers manufactured on or after March 1, 1979 need them mounted 15 to 60 inches above the road surface.
- Front and intermediate side markers: amber. Longer trailers need amber lamps near the midpoint of the trailer’s length. We explain the length thresholds in our marker light rules guide.
- Clearance and identification lamps: required on trailers 80 inches or wider. Amber faces the front. Red faces the rear. The rear identification cluster is three red lamps.
- Reflectors: red at the rear, amber on the sides toward the front and middle. Reflectors need to work with no power at all, which is why they matter when the electrical system fails.
A note on dual-color hardware: a lamp that is red on one face and amber on the other is built to cover both positions. A 2-inch round red/amber clearance light or a square red/amber marker with reflectorized lens is chosen by the lens color for the position it goes in. Buy the color the spot calls for, not the one that looks best.
For a stick-on reflector, a Class A 3-inch round reflector in red or amber follows the same rule: red to the rear, amber to the front and sides near the front or middle.
License plate lamp
The license plate lamp is the only white lamp facing the rear that is always required. Keep it dedicated to lighting the plate. White light that points backward from anywhere else is also a potential issue, since it looks like a reversing lamp. If your trailer has a backup lamp, it is a separate, optional white function, wired separately from the plate light.
Federal rules versus state rules
Federal rules apply directly to commercial motor vehicles in interstate commerce, and state law covers everyone else on the road, often with similar language. Two things matter:
- Most states follow the same color logic. Red to the rear, amber to the front, white for the plate.
- The details around it differ. Which trailers need which lamps, and how certain lights are described, is set by each state.
Here are examples straight from state sources:
- California’s DMV handbook says trailers need reflectors, tail, brake and license plate lights, with clearance lights on trailers over 80 inches wide.
- New York requires that 1966 and newer trailers have two rear turn signal lamps that operate with the towing vehicle’s hazard warning system.
- Pennsylvania prohibits ornamental lamps that aren’t enumerated or located as specified, and requires lamps to have permitted colors that are not obscured or altered by auxiliary equipment.
If you run across state lines, build to the stricter reading. A trailer set up with red rear lamps, amber front and intermediate markers, a white plate lamp, and DOT-marked lenses satisfies the common denominator everywhere.
Add-on lights, glow lighting and sleeper accents
Drivers regularly ask whether they can run colored accent lights on a trailer rear or the back of a sleeper. The honest answer is that it depends on color, position and effect, not on a single yes or no.
NHTSA has looked at this twice in ways that are helpful:
- In an older interpretation, it said auxiliary lamps at the top rear of a trailer may be permissible when they do not impair or confuse required lighting. In the example reviewed, lamps on the edges were fine because they did not interfere with the three-lamp center identification cluster.
- In an April 2025 interpretation, NHTSA said an aftermarket auxiliary device at the rear of a trailer may conflict with FMVSS No. 108 when its colors and location could impair required side-marker lamps. It specifically noted that rear side markers must be red and intermediate side markers amber.
The reasoning behind both: color and location together decide whether a driver behind you can tell the front from the rear or the midpoint, especially at night or in poor weather. Blue, green or flashing accent colors on a trailer also create problems in states that restrict those colors for emergency or authority use, so check your state code before adding them.
A practical rule for any extra lamp:
- Keep it away from the required positions and the identification cluster.
- Never use a color that reads as the wrong position (amber at the rear, red at the front).
- Don’t make it flash or move.
- Wire it on its own switch so it is off when you are on the road.
Work or strobe lighting is its own topic with its own state-by-state rules, which we cover in our strobe light laws guide.
Wiring colors: convention, not law
The federal and state rules above set lamp colors, not wire colors. No lighting regulation tells you what color insulation a trailer’s wires must have. What you see in practice is a widely followed convention.
On a standard 4-pin flat connector, the usual arrangement is:
| Wire color | Typical function |
|---|---|
| White | Ground |
| Brown | Tail, running and marker lights |
| Yellow | Left turn and brake |
| Green | Right turn and brake |
Larger connectors add circuits, such as electric brakes (commonly blue), a battery or auxiliary feed and reverse lights. Commercial trailers with 7-way round plugs follow a similar scheme, but conventions in older equipment and aftermarket harnesses are not perfectly consistent.
That inconsistency is why we say: test, don’t trust. Before connecting a lamp, use a test light or a tester at the plug to confirm which pin does what. Then:
- Use copper or copper-clad wire sized for the load, since voltage drop makes lamps dim.
- Ground to clean bare metal, or run a dedicated ground wire.
- Seal every connection with grommets, plugs or heat-shrink so water stays out.
An LED lamp that looks dim or flickers is usually a ground or connection problem, not a bad lamp.
Quick compliance check before you roll
Walk the trailer at dusk with the lights on and a helper at the back.
- Two red tail lamps on, evenly spaced, the same brightness.
- Press the brake: both red stop lamps brighten, and the third brake lamp (if fitted) lights.
- Each turn signal flashes at a normal pace, and hazards flash both sides together.
- Red side markers at the rear, amber at the front and midpoint of the side.
- Clearance lamps: amber forward, red rearward, and three red identification lamps at the rear on wide trailers.
- White plate light shows the plate clearly.
- Reflectors present, clean, uncracked and in the right color.
- No cracked lenses, no water inside, no faded lens color.
The California commercial driver handbook stresses that lighting checks are critical because working lights let drivers see, be seen and signal other traffic. For a longer fleet-oriented inspection list, see our DOT lighting checklist.
Perspective
We see the same mistakes over and over. A replacement lamp comes in the wrong color for its position. A lens fades from red to a washed-out orange. A lamp that was never sealed fills with water. None of these are exotic, and all of them are avoidable at the time you buy.
Our approach is to build lamps for the position they will occupy: red where the rule calls for red, amber where it calls for amber, with lenses and reflectors designed to meet FMVSS 108 and DOT requirements. We design our LED lamps with leak-proof housings and bright LEDs, and our wiring with thicker copper, because a lamp that stays lit in rain, road salt and vibration is the only one that keeps you compliant after the first month.
Our advice to fleets and builders: standardize on certified lamps, match colors to positions across the whole trailer, and keep wiring and sealing consistent from unit to unit. It makes inspections quicker and repairs simpler.
All
Lighting built for the right position
If you are replacing lamps or building out a trailer, start with the lighting that matches your layout. For a full rear set, our red, white and amber 6-inch oval stop/turn/tail kit comes with grommets and plugs and an IP67 waterproof rating. For a wide trailer, the rectangular 42-LED tail light kit is made for 80-inch-wide trailers. Browse the full range of lighting, wiring and reflective products on our main site.
Before ordering, check the lens color against the position it will occupy, and match the lamp count to your trailer’s width and length.
FAQ
Do trailer turn signals have to be amber?
No. On commercial vehicles, rear turn signals may be red or amber. Front and near-front turn signals must be amber. Check your state code too, since some use slightly different wording.
What color must trailer side marker lights be?
Rear side markers must be red, and front and intermediate side markers must be amber. NHTSA’s interpretations confirm this split for trucks and trailers. The color follows where the lamp sits on the trailer, not the lamp style.
Can I put colored accent lights on my trailer?
Sometimes, but not in the positions or colors that would confuse required lamps. NHTSA looks at color and location together, and states can restrict ornamental lighting. Keep accents off the required positions and the rear identification cluster, and read your state’s rules first.
Do trailer wire colors have to follow a standard?
No law sets wire insulation colors. Most 4-pin connectors use white for ground, brown for tail and marker lights, yellow for left turn and green for right turn. Confirm each circuit with a tester before connecting anything.
Does the license plate lamp have to be white?
Yes. Federal rules call for a white license plate lamp, and trailers need one that lights the plate. Keep it separate from other white lamps such as backup lights.
Sources
- 49 CFR Part 393 Subpart B: Lamps, Reflective Devices and Electrical Wiring (eCFR)
- NHTSA interpretation 21872.ztv
- NHTSA interpretation GF007705
- NHTSA interpretation NCC-230420-001, auxiliary side lamps
- Ohio Administrative Code Rule 4501-15-04
- Texas Transportation Code Chapter 547
- Texas DPS: Lighting
- California DMV Recreational Vehicles and Trailers Handbook
- New York DMV: Equipment Required for Trailers
- 67 Pa. Code § 175.125
- California Commercial Driver Handbook (Spanish supplement)
Recommended
- Red/White/Amber 4" Round LED Trailer Tail Light 24 LED Chrome Bezels Stop Turn Tail Brake Signal Reverse Backup Marker Lights Trucks Trailer RV Camper Dump Truck Waterproof
- Trailer Plug Wiring Colors: Shop Tested Charts and 5 Mistakes to Avoid
- 4" Round Amber/Red/White LED Trailer Tail Light 18 LED Stop Turn Signal
- Red/White/Amber 6" Oval 10 LED Trailer Stop Turn Tail Light Kit DOT Certified




