Energy Efficient Truck Lights: What to Buy and How to Fit Them
The most energy efficient truck lights are LEDs. A truck or trailer lamp in LED form uses roughly one-tenth of the current of an incandescent bulb, which takes load off the alternator and the wiring. Efficiency only pays off if the light is also DOT-compliant, sealed against water and road salt, and wired so the truck’s electronics read it correctly. This guide covers all four: which lights to convert, what the rules say, how to wire them, and how to make them last.
TL;DR
- LED warning and marker lamps draw less than 10% of the amps of incandescent bulbs for the same output, which reduces demand on the alternator.
- Efficiency does not replace compliance. Replacement lamps must meet FMVSS No. 108, and a lamp built for a bulb may not perform the same with an LED dropped in.
- Corrosion, not the LED itself, is what usually ends a lighting system. Sealed housings, sealed connectors and correct wire gauge protect the savings.
- Some late-model trucks read low LED current as a fault. Check trailer-detection and bulb-out behavior before you convert a whole rig.
Table of Contents
- Why LEDs are the energy efficient choice for trucks
- Which truck and trailer lights come in energy efficient LED versions
- What the rules say: efficiency has to be compliant
- Wiring and electrical compatibility
- Making the savings last: sealing and corrosion
- Trailer lighting: where the efficiency gains are easiest
- Headlights: brightness is not the only measure
- Our perspective
- Get the full set from one place
- FAQ
- Sources
Why LEDs are the energy efficient choice for trucks
Incandescent lamps turn most of their electricity into heat. LEDs turn far more into light, so the same brightness needs much less current. An Idaho Transportation Department briefing on LED warning lights puts the figure at under 10% of the amps of incandescent bulbs. Trade press on trailer lighting says the same thing in simpler terms: LED lamps use about one-tenth the current of incandescent bulbs.
What does that mean on a working truck?
- Lower electrical load. A tractor and trailer can run dozens of lamps at once: markers, clearance lights, stop, turn and tail lamps, plus identification lights. Cutting the draw of each one cuts the total.
- Less strain on the charging system. The U.S. Department of Energy has estimated that converting large-truck and bus lighting to LEDs could save onboard electricity and diesel fuel. The effect per truck is modest, but it adds up across a fleet and across years.
- Less heat at the wiring. Lower current means less heating in connectors and wire, which is easier on a trailer harness that has been in service for years.
- Better visibility for the energy spent. Truck makers have pointed out that LED headlamp light is close to daylight in color, which they say helps reduce eye strain and fatigue on night drives. That is a manufacturer’s position, not a lab result, but it matches what many drivers report.
A caution on the word “energy.” The savings are real but small next to your fuel bill. The stronger case for LEDs on commercial vehicles is that they cut the electrical load and the replacement work at the same time. A lamp that does not burn out has no downtime.
Which truck and trailer lights come in energy efficient LED versions
Nearly every exterior lamp on a commercial vehicle now has an LED version. Here is how the main categories break down.
| Light type | Where it goes | What to look for |
|---|---|---|
| Marker and clearance lights | Cab roof, cab sides, trailer corners and sides | DOT/SAE marking, correct color (amber front and side, red rear), sealed lens |
| Tail, stop and turn lights | Rear of truck and trailer | FMVSS 108 compliance, matched pairs, sealed grommet and plug connections |
| Cab and roof lighting | Top of cab, running-light bars | Heavy-duty housing, correct amber output, vibration tolerance |
| Headlights | Front of the tractor | Beam pattern designed for the housing, not just a bright bulb |
| Strobe and warning lights | Service, tow and yard vehicles | Local rules on color and use, current draw in the spec |
| License plate lights | Rear plate area | White light, plate visible at the required distance |
| Reflective tape and reflectors | Sides and rear of trailers and tractors | Passive, so no power draw, but required for conspicuity |
Reflective tape and reflectors use no electricity at all. They are still part of an efficient visibility package, because they keep the trailer visible when lamps fail or when the truck is parked. For the rules on marker placement, our guide to marker light rules for U.S. fleets lays out what has to be where.
For the lamps themselves, a few places to start:
- Cab and marker positions on Peterbilt, Kenworth and Freightliner trucks: our 20 LED amber/red marker lights with turn signal function are made for those positions.
- Cab roof running lights: the 17 LED amber torpedo cab marker lights replace old incandescent torpedo lamps.
- Trailer rear lighting: sealed rectangular lamps, covered below.
What the rules say: efficiency has to be compliant
In the U.S., lamps and reflective devices on trucks and trailers fall under Federal Motor Vehicle Safety Standard No. 108. NHTSA describes the standard as covering original and replacement lamps, reflective devices and associated equipment on trucks and trailers, to provide roadway illumination and improve conspicuity. The full text in the eCFR also requires conspicuity systems on applicable trailers and truck tractors, and requires lamps and reflectors to be mounted securely on rigid parts of the vehicle, within set locations and height limits, and to meet photometric and visibility requirements.
Two practical points follow from NHTSA’s own interpretation letters.
Replacement lamps must meet the same standard as the original. NHTSA has said that replacement lighting equipment must be designed to conform to the standard in the same manner as the original equipment. It also warns that putting an LED into a lamp designed around an incandescent source may negatively affect photometric performance. In practice, that means you should buy a complete LED lamp that is marked for DOT use, not an LED bulb in an old housing, when the lamp is a required safety device.
Road use is also a state question. In the same interpretation, NHTSA states that whether replacement equipment such as LEDs may be used on public roads is a matter of state law, not federal law. If you run across state lines, check your home state’s rules and those of the states you run in, and keep the DOT/SAE markings readable on every lens.
To see how inspectors look at this in practice, use our DOT lighting checklist for U.S. fleets. For plate lamps, which are often forgotten, see license plate light requirements for trucks and trailers.
Wiring and electrical compatibility
LEDs draw less current, which is the whole point. But it creates a few things to check before you convert.
Wire gauge still matters
Lower current does not mean you can use thin wire. SAE J1292 calls for at least 12-gauge feed wires for exterior lamps on trucks 80 inches or wider, with 14-gauge allowed for branches or taps up to 50 feet. The same standard calls for wiring to be protected from corrosion and road splash. Keep those gauges as your floor when you rewire, and choose copper or copper-clad conductors in a harness that is sealed at every joint.

Check what the truck’s electronics expect
Low draw can confuse a vehicle that monitors its lamps. A 2022 NHTSA-published service bulletin on 2019 to 2022 Silverado and Sierra pickups with the U1D option says some non-DOT-approved LED lamps may not draw enough current for the trailer module to detect the trailer. The fix it lists is incandescent lamps or DOT-approved LED lamps. That is a pickup example, but the principle holds for any vehicle that counts lamp load.
Academic work on heavy-duty vehicles describes the same issue: older central control units may mistake an LED’s low power draw for a lighting fault. The common remedies are passive load resistors, which waste some of the energy you just saved, or an energy-recovery unit that lets the control unit see the load while returning the excess to the battery. If your truck throws bulb-out warnings after a conversion, that is the cause to investigate before you blame the lamps.
A pre-conversion checklist
- List every lamp position on the tractor and trailer, and note which ones the truck monitors.
- Confirm each replacement is a complete DOT/SAE-marked lamp for that position.
- Check the existing harness for green corrosion, brittle insulation and exposed conductors. Replace what is damaged.
- Confirm feed and branch wire gauge against the SAE minimums above.
- Convert one position first on vehicles with lamp-out monitoring, and test before converting the rest.
- Re-test stop, turn, tail and marker functions with the trailer connected.
Making the savings last: sealing and corrosion
An LED rated for tens of thousands of hours does not help if water gets into the lamp or plug. Trade reporting on trailer lighting notes that corrosion remains a major problem for LED lamps and electrical systems, and that aggressive de-icing chemicals splashed onto trailers make it worse. The Technology & Maintenance Council recommends treating new trailer lighting as a whole system: sealed wiring, water- and corrosion-resistant connectors and low-amperage lamps, aiming for a system service life of at least 12 years.
Two more points from the field:
- LEDs are generally reliable, but board quality and driver circuits differ between makers, and the optics decide how the light is used. A cheap lamp can fail early even though LEDs as a technology last.
- Failures often start at the plug and the grommet, not in the lamp. Our guides on corrosion resistant wiring and on stopping 7 pin trailer plug corrosion go step by step.
When a flickering lamp turns out to be a charging or battery problem rather than wiring, a technician who comes to your location can save a trip. Mobile vehicle maintenance covers things like battery and alternator work at the roadside, which is where electrical faults tend to show up.
Trailer lighting: where the efficiency gains are easiest
Trailers are where many fleets start, because the lamps are simple, numerous and exposed to the worst of the weather. A full set of sealed LED lamps on a trailer can be swapped in an afternoon, and the harness gets the biggest benefit from the lower current.
Look for:
- Submersible, sealed construction, especially for boat trailers, dump trailers and anything that sees wet roads in winter. Our guide to submersible LED trailer lights and matched kits explains what the ratings mean.
- Matched kits with the harness, grommets and plugs included, so you are not mixing old and new connections.
- Compliant rectangular lamps for tail, stop and turn positions on trailers 80 inches or wider. Our 42 LED rectangle tail light kit is marked for FMVSS 108.
- Smaller kits for narrow trailers, like the 12V LED trailer light wiring kit for utility, boat and camper trailers under 80 inches, or the low profile submersible rectangle kit with a 25 ft 4-pin harness.
Headlights: brightness is not the only measure
Headlights are where “efficient” and “better” are easiest to confuse. A brighter lamp that scatters light creates glare for oncoming drivers and gives you no more usable road. The question to ask is whether the beam pattern is designed for the housing it sits in. Our comparison, LED vs halogen headlights for fleets, looks at glare and visibility in more detail. Headlamps are also covered by the same replacement-equipment principle above: the optics decide how the light lands on the road.
Our perspective
We build our lighting for people who cannot afford a dark trailer: drivers on long hauls, fleets with a lot of lamps in service, and shops that rewire units for a living. From that point of view, efficiency is a result of good design and not a goal in itself.
Our LEDs are designed to run bright on low current. Our housings are designed to stay leak-proof, so water does not shorten that life. Our copper and copper-clad wiring, connectors and grommets are designed to be fitted as a system with the lamps, because most failures we hear about start at the connection and not at the diode.
Our products are built to meet and, by our design goals, exceed DOT requirements. For a fleet manager, that means a lighting package where the lamps, wiring and reflective tape come from one place and are meant to work together. That is how we think a truck should be lit: bright, compliant, sealed and easy to service.
All
Get the full set from one place
If you are converting a truck or trailer, buy the lamps, wiring, grommets and plugs together so that the sealing is consistent from end to end. We stock DOT-compliant LED marker, tail, cab and roof lights, reflective tape, wiring harnesses, copper and copper-clad wire, connectors and grommets for trucks, trailers and commercial vehicles.
Browse the full range of lighting, wiring and reflective products and match each position on your rig to a compliant lamp. If you are not sure which lamps your trailer needs, start with the DOT lighting checklist.
FAQ
Do LED truck lights really use less power?
Yes. Sources from a state transportation agency and the trucking trade press put LED current draw at about one-tenth that of incandescent bulbs for comparable output. That lowers the load on the alternator and the heat in the harness. The savings are largest on trailers and cab marker positions, where many lamps stay on for hours.
Can I put LED bulbs in my existing truck lamps?
Not safely for required safety lamps. NHTSA says replacement equipment must conform to FMVSS 108 the way the original did, and that swapping LEDs into a lamp designed for an incandescent source can hurt photometric performance. Buy a complete DOT/SAE-marked LED lamp for that position. Also check your state’s rules, since NHTSA leaves road-use questions about replacement equipment to the states.
Why does my truck show a bulb-out warning after an LED swap?
Some vehicles detect lamps by measuring current, and an LED’s low draw can look like a failed bulb. Service bulletins and research describe fixes such as using DOT-approved LED lamps, adding a load resistor, or using an energy-recovery unit. Test one position before converting the whole truck.
What wire size should I use for LED truck lights?
For trucks 80 inches or wider, SAE J1292 specifies at least 12-gauge feed wires for exterior lamps, and 14-gauge for branches or taps up to 50 feet. It also calls for protection from corrosion and road splash. Use those as minimums, and use sealed connectors at every joint.
Do reflective tape and reflectors count as energy efficient lighting?
They use no power, so they are the most efficient visibility product on the vehicle. FMVSS 108 requires conspicuity systems on applicable trailers and truck tractors, so they are required equipment, not an extra.
Sources
- Idaho Transportation Department: LED light bars
- Trucking Info: Two things you should know about trailer lighting and wiring
- U.S. Department of Energy: Solid-state lighting niche final report
- International: LED headlights now standard on ProStar trucks
- NHTSA: FMVSS 108 compliance test procedure TP-108-13
- eCFR: 49 CFR 571.108, Standard No. 108
- NHTSA interpretation: replacement LED equipment
- SAE J1292 wiring specification
- NHTSA service bulletin on trailer detection with LED lamps
- MDPI: Energy-recovery unit for LED lighting in heavy-duty vehicles
- Interfacing truck and trailer lighting
- Mobile vehicle maintenance




