Skip to content
Wish lists
Wish lists
Cart
1 item

Keep Truckin’ Blog

Clearance Light Placement on Trucks and Trailers: U.S. Rules

by Frank A. 27 Oct 2026 0 comments

Clearance lights go at the top corners of the vehicle, one on each side of the vertical centerline, at the same height and as high as practicable, so other drivers can read your overall width. Amber faces forward, red faces the rear. They are required on trucks, tractors and trailers that are 80 inches wide or wider. The details below cover exactly where each lamp goes, what you can do when the ideal spot is not practical, and what inspectors look for.

Allstartruckparts
Choose Lights Built for the Road
Explore DOT-compliant truck and trailer lighting designed for harsh weather, including headlights, trailer lights, wiring, and reflective tape.
Explore lighting products

TL;DR

  • Clearance lamps mark overall width (and height). Mount them in pairs, one each side of the centerline, at the same level and as high as practicable.
  • Front clearance lamps are amber and rear ones are red. Federal rules apply to vehicles 80 inches (2,032 mm) or wider.
  • On a tractor, cab-mounted clearance lamps may indicate the width of the cab instead of the vehicle.
  • Lamps can sit away from the extreme corner to protect them from damage, but only if they still show overall width and stay as close to the top as practicable.
  • Every required lamp must work. A dead clearance light is a violation, not a cosmetic issue.

Table of Contents

What clearance lights actually do

A clearance lamp has one job: show another driver how wide your vehicle is, and how high its top corners sit, when they only see lights. At night, on a two-lane road or at a tight interchange, the pair of lamps at the upper corners is what tells an oncoming driver that a wide box is coming.

That is why placement matters more than brightness. Federal rules say clearance lamps are intended to show to the front or rear and must be mounted on the permanent structure as near as practicable to the upper left and right extreme edges to indicate overall width and height. A bright lamp sitting at mid-height in the center of a panel still fails that purpose.

If you also need the difference between clearance and side marker lamps, our guide to clearance vs marker lights and the 80 inch rule covers it in depth. Here we stay on placement.

The federal placement rule in plain words

The core requirement sits in 49 CFR 393.11. Clearance lamps go at the front and rear, one on each side of the vertical centerline, at the same level and as high as practicable, to indicate overall width. Break that into four checks:

  1. Pairs. One lamp on each side of the vertical centerline, never two on the same side standing in for a pair.
  2. Matched height. Both lamps in a pair sit at the same level. A left lamp noticeably lower than the right one distorts the shape drivers read.
  3. As high as practicable. Push them to the top of the structure, not to a convenient flat spot halfway down.
  4. Facing the right way. Front lamps show forward, rear lamps show rearward.

Color and direction

Front clearance lamps are amber and rear clearance lamps are red, with each pair positioned on opposite sides of the vertical centerline to indicate overall width, according to the same federal table. “Which way do clearance lights go” has a short answer: the amber lens toward the front of the vehicle, the red lens toward the back. On a double-face lamp such as a trailer corner pedestal, one side is amber and the other red, so the orientation of the fixture is the whole point.

Which vehicles need them, and how many

The requirement follows width. Under the federal table, clearance lamps are required on buses and trucks 2,032 mm (80 inches) or more in overall width, truck tractors, semitrailers and full trailers of that width, and pole trailers.

Vehicle Front clearance (amber) Rear clearance (red)
Truck or bus, 80 in. or wider 2 2
Truck tractor 2 Not required on the tractor itself
Semitrailer or full trailer, 80 in. or wider 2 2
Pole trailer 2 2
Projecting load 2 2

The table is built from the federal list: two amber front lamps for wide buses and trucks, truck tractors, wide trailers, pole trailers and projecting loads, and two red rear lamps for the same groups except tractors.

The common trailer setup is therefore four clearance lamps: two amber at the front upper corners and two red at the rear upper corners. Many trailers use a double-face pedestal lamp at each corner that serves as the front amber and rear red lamp in one fixture. That works when the fixture sits where both functions meet the placement rule.

Boat trailers

There is one narrow exception worth knowing. A boat trailer 80 inches or wider may use a single amber and red clearance lamp at or near the midpoint of each side instead of separate front and rear lamps, if that indicates extreme width. Most commercial haulers will never use it.

Placement on a truck tractor

Tractors are where most placement questions come from, because the cab is often narrower than the trailer it pulls. The rule gives a clear answer: for truck tractors, clearance lamps mounted on the cab may indicate the width of the cab rather than the width of the whole vehicle (Footnote 15).

In practice that means the amber lamps go on the upper corners of the cab roof or visor line, one on each side of the cab centerline, at the same height. Many tractors also carry a three-lamp amber identification cluster centered above the windshield. Those are separate from clearance lamps and are described below.

Do not read that footnote as permission to use cab lamps on every vehicle. NHTSA has said that on vehicles such as tank trucks or flatbeds, clearance lamps must be mounted at the widest point of the vehicle, and cab-mounted lamps are not a universal substitute.

Placement on a trailer

On a trailer the geometry is simpler. The rear lamps go at the top rear corners, red, facing back. The front lamps go at the top front corners, amber, facing forward. On a dry van or reefer this means the upper corner of the box. On a flatbed, there is no tall structure, so the lamps go at the widest point of the deck, which is the point NHTSA’s interpretation above addresses.

Front and rear trailer clearance lamp positions

When the corner is not practical

The rule is not rigid. Clearance lamps may be placed elsewhere if necessary to indicate width or to protect them from damage during normal operation. NHTSA’s reading is that lamps may sit away from the extreme front or rear for protection, provided they still indicate overall width and are as close to the top as practicable.

That is the logic behind short pedestal and fender-mounted lamps on flatbeds, dump bodies and cargo trailers that get hit by loaders and dock plates. A lamp moved inboard a few inches to survive the next forklift still passes, as long as it reads as the edge of the vehicle.

There is a photometric consequence. Lamps mounted for protection away from the extreme front or rear need not meet the output at any test point 45 degrees inboard, though they must meet all the other test points.

Identification lamps change the rear rule

When rear identification lamps are mounted at the extreme height of a vehicle, the rear clearance lamps are not required to be located as close as practicable to the top. That is why you see many trailers with a red three-lamp bar centered at the top rear and the red clearance lamps a little lower on the corners.

Clearance, identification and side marker lamps: keep them straight

These three get mixed up constantly, and mixed-up lamps are how trailers end up with the wrong color in the wrong place.

Lamp Where it goes What it shows
Clearance High, on opposite sides of the vertical centerline Overall width
Identification Three-lamp cluster near the top, on the centerline That a wide vehicle is present
Side marker On each side of the vehicle Length of the vehicle from the side

This summary follows the same federal lighting table. Our marker light rules guide covers the side marker requirements for longer vehicles in detail.

Two combination rules matter at the bench. First, FMVSS 108 prohibits optically combining a clearance lamp with a taillamp. Second, a combination lamp serving both clearance and side marker functions must, per NHTSA, emit light over a 180-degree wide angle to satisfy both sets of photometric requirements. A double-face pedestal that sits at the corner is built for this.

A mounting checklist for installers

Use this order on a new build or a retrofit:

  1. Measure the width. If the vehicle is 80 inches or wider, you need clearance lamps.
  2. Mark the centerline and a matched height on both sides before drilling.
  3. Pick the highest practical position on the permanent structure, not on a removable panel or tarp bow.
  4. Check visibility. Nothing, including ladders, hinges, doors or a ramp, should block the lens. NHTSA’s guidance on rear lighting says installers should confirm at least two square inches of lens area is visible at 45° left and 15° right, and where equipment prevents that, auxiliary lamps that meet the visibility requirements are needed.
  5. Confirm color and direction. Amber front, red rear.
  6. Seal the wiring. Use sealed connectors and grommets where the harness passes through sheet metal, because moisture at a corner lamp is the most common reason it fails inside a year.
  7. Test every lamp with the running lights on before the vehicle leaves the shop.

Will a dead clearance light get you written up?

Yes. Under 49 CFR 393.9, all required lamps must be operable, and a lamp mounted so that it blocks the required light spread is also non-compliant. The same section says it does not require auxiliary or additional lamps to be operable at all times, which means a required clearance lamp is held to a stricter standard than an optional work light.

For fleets, this is the cheapest violation to prevent. A walk-around that touches every corner lamp takes under two minutes. Our DOT lighting inspection checklist lays out the full walk-around in order.

Our perspective: place for the worst day, not the best one

Most clearance light failures we hear about are not electrical. They are placement decisions made for convenience: a lamp low on a bumper corner because the roof rail was hard to reach, a harness run past a sharp edge, a lens aimed into a ladder. The lamp works on the bench and fails the first wet winter.

Our view is simple. Put the lamp where the rule intends, as high and as wide as the structure allows. If that spot gets hit, use the protected-position allowance the regulation provides, and choose a fixture built to live there: sealed housing, strong lens, a secure mount. Then seal the wiring entry as carefully as the lamp itself, because water follows the harness.

That is also how we think about the products we sell. Leak-proof housings, bright LEDs and thicker copper wiring matter most at the corners of a vehicle, where vibration, road spray and impacts are worst. Placement gets you compliant, and construction keeps you compliant for years.

— All

Choosing lamps that suit the position

The right fixture depends on where it is going.

Ready to replace or build out a set?

All Star Truck Parts sells DOT-compliant LED marker and clearance lighting, sealed housings, wiring, connectors and grommets for trucks and trailers. If you are rebuilding a corner or equipping a new trailer, start with our marker and clearance lighting and pick lamps and harness parts together so the whole circuit is sealed the same way.

RED 3 LIGHT COMBINATION CLEARANCE ID BAR MARKER 24 LED TRAILER IDENTIFICATION

Common placement mistakes to avoid

  • Mismatched heights. Left and right lamps at different levels make the vehicle look skewed.
  • Lamps too far inboard. If the pair no longer shows the real edge of the vehicle, the width signal is wrong.
  • Cab lamps on a flatbed or tank. The cab footnote is for truck tractors. Straight trucks and tanks need lamps at the widest point.
  • Red facing forward or amber facing back. Check double-face fixtures before tightening the nut.
  • Blocked lenses. Ladders, ramps, mud flaps and cargo straps can hide a lamp that technically works.
  • Unsealed wire entry. A grommet missing at a panel pass-through can let water into a harness and take out a whole side.

FAQ

How many clearance lights does DOT require?

For a vehicle 80 inches or wider that needs them, the federal table calls for two amber lamps at the front and two red lamps at the rear, with one on each side of the centerline. Truck tractors need the two front amber lamps. Check the vehicle type in 49 CFR 393.11 for any special case.

Which way do clearance lights go?

Amber lamps face forward and red lamps face rearward. On a double-face fixture, the amber lens points toward the front of the vehicle and the red lens toward the back. Always check the orientation before final tightening.

Is a clearance light out a DOT violation?

Yes. Required lamps must be operable, so an inoperative clearance lamp is a violation that can show up in a roadside inspection. Fix it before the trip, and replace the whole lamp or its harness when moisture is the cause.

Are clearance lights required on every trailer?

No. The federal requirement follows width: trailers and trucks 80 inches or wider need them. Narrower vehicles may still need other lamps and reflectors, and some states add their own rules, so check your state’s requirements as well.

Sources

Sample Image Gallery

SPRING SUMMER LOOKBOOK

Sample Block Quote

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis.

Sample Paragraph Text

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis nec danos dui. Cras suscipit quam et turpis eleifend vitae malesuada magna congue. Damus id ullamcorper neque. Sed vitae mi a mi pretium aliquet ac sed elitos. Pellentesque nulla eros accumsan quis justo at tincidunt lobortis deli denimes, suspendisse vestibulum lectus in lectus volutpate.
Prev post
Next post

Leave a comment

Please note, comments need to be approved before they are published.

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Edit option
Back In Stock Notification

Choose options

this is just a warning
Login
Your Cart Good Picks!
Free shipping in all us ORders