Side Marker Spacing on Trucks and Trailers: What the Rules Require
Federal rules do not give you a fixed interval such as “one lamp every X feet.” They fix the positions instead: one amber lamp as far forward as practicable on each side, one red lamp as far to the rear as practicable, and on vehicles longer than 30 feet, an extra amber lamp at or near the midpoint. Every side marker must also be at least 15 inches off the road. The rest of this guide shows how that works on real equipment, where state rules add detail, and how to check your own trailer before an inspector does.
TL;DR
- Front side markers are amber and rear side markers are red, each placed as far toward its end of the vehicle as practicable (49 CFR 393.11).
- On applicable vehicles over 30 feet, add an intermediate amber marker lamp and an amber reflector on each side, at or near the midpoint.
- Mount side marker lamps at least 15 inches above the road. Rear side marker lamps on trailers must not be higher than 60 inches.
- Texas requires four side markers and four reflectors on vehicles at least 80 inches wide, plus central markers over 30 feet long.
- Do not add auxiliary lamps that could be confused with required lighting, and do not combine a clearance lamp with a tail or identification lamp.
Table of Contents
- Why there is no single “spacing” number
- The federal layout, position by position
- Height and mounting rules
- Colors and the front-to-rear logic
- Trailer side turn signals
- The 80-inch width line and Texas
- Choosing lamps that fit the layout
- Perspective: what we see on the install bench
- Install and inspection checklist
- Ready to replace or add markers
- FAQ
- Sources
Why there is no single “spacing” number
Most people who search for side marker spacing want a distance: how far apart do the lamps go? In the United States the answer is built from three things, not one: the end positions, a length trigger at 30 feet, and a height window.
Some sites you will find online quote an interval between lamps, such as a maximum of 3 metres. That figure comes from rules outside the U.S. The federal table in 49 CFR 393.11, which governs commercial vehicles in interstate commerce, writes the requirement as locations: “as far to the front as practicable,” “as far to the rear as practicable,” and “at or near the midpoint” for the intermediate position. If you are building or repairing a trailer for the U.S. market, those are the words you work to.
That means two trailers of different lengths end up with different gaps between lamps, even though both are compliant. A 28-foot trailer needs only the front and rear pair. A 53-foot trailer needs the middle pair too, so the gaps shrink to roughly a quarter of the body length each.

The federal layout, position by position
The table in 49 CFR 393.11 sets the counts and positions for each lamp and reflector type. For side markers on a standard applicable vehicle, it breaks down like this.
| Device | Color | Quantity | Position | Height |
|---|---|---|---|---|
| Front side marker lamp | Amber | 2 (one per side) | As far to the front as practicable | Not less than 15 inches |
| Intermediate side marker lamp | Amber | 2 (one per side) | At or near the midpoint between front and rear markers, if the vehicle is over 30 feet | Not less than 15 inches |
| Rear side marker lamp | Red | 2 (one per side) | As far to the rear as practicable | Not less than 15 inches; trailers not more than 60 inches |
| Intermediate side reflex reflector | Amber | 2 (one per side) | At or near the midpoint, if the vehicle is over 30 feet | Between 15 and 60 inches |
Pole trailers and converter dollies have their own provisions in the same section, so check the table’s entry for those rather than assuming the standard layout.
The FMVSS No. 108 interpretation from NHTSA confirms the same basic pattern for trailers: two amber side marker lamps at the front and two red ones at the rear.
What “as far as practicable” means in the shop
The phrase gives you some room, but not much. On a flatbed, the front marker goes at the front of the deck or the headboard, not halfway back on a fender because it was easier to wire. On a van trailer, the rear marker sits near the rear corner post, and the front marker near the nose. If the structure blocks the ideal spot, move the lamp the shortest distance that works and keep it visible from the side.
The 30-foot trigger
The intermediate position is where most spacing mistakes happen. The table ties it to vehicle length: when the vehicle is more than 30 feet (9,144 mm), you add the amber intermediate marker and amber intermediate reflector on each side. They go at or near the midpoint between the front and rear marker lamps, not the midpoint of the whole vehicle including the tongue.
A practical way to find it: measure between the center of your front marker and the center of your rear marker, divide by two, and mark that point on the rail or skin. Then adjust for a crossmember, rivet line or door seam, staying as close to the mark as the structure allows.
If you are routing wire for a long trailer anyway, that is also a good moment to check what else is on the harness. Owners adding an integrated trailer brake controller to a tow vehicle, for example, are already testing the trailer’s connector, so confirm the marker circuit while the plug is in hand.
Height and mounting rules
Height is the part of the rule that is simple and strict. Side marker lamps must be mounted at least 381 mm (15 inches) above the road surface. Rear side marker lamps on trailers must be no more than 1,524 mm (60 inches) high. NHTSA’s long-standing interpretation of the mounting height sits in the same range for lamps, with reflex reflectors treated separately.
Two practical notes from the regulation:
- Measure from the center of the lamp. A tall pedestal lamp on a low fender can pass or fail depending on where you measure, so measure the lamp’s center, with the vehicle at its normal loaded ride height where you can.
- Mount to something rigid. Section 393.25 requires lamps to be securely mounted on a rigid part of the vehicle. Temporary lamps may be mounted to the load. A marker lamp zip-tied to a flexible mud flap will drift out of position and out of compliance.
Lamps also have to face the way they are meant to. The rule of thumb from trailer lighting guidance is that lights are installed square to the trailer’s centerline, so rear lights face rearward and side lights face outward, not angled off where the mounting surface happens to point.
Colors and the front-to-rear logic
The color rule is the easiest to remember: amber toward the front, red toward the rear. The New York DMV commercial driver manual tells drivers to check side marker and identification light colors on the walk-around, amber at the front and red at the rear, which is exactly what an inspector will do.
Identification lamps are a separate group. The three-lamp cluster on the rear of a trailer is a different system from side markers, and NHTSA has told manufacturers that auxiliary lamps must not interfere with or be confused with that cluster. So a decorative row of red lamps near the top rear corners is a compliance problem, not just a style choice.
Combining lamps
Federal rules also restrict how lamp functions share a housing. 49 CFR 393.22 prohibits optically combining a clearance lamp with a tail lamp or identification lamp. A turn signal lamp cannot be combined with a stop lamp unless the stop lamp is deactivated when the turn signal is on. Side marker lamps that double as turn signals (common on pedestal fender lights) are built to handle this, which is why the wiring type matters when you buy.
Trailer side turn signals
Readers often ask about side turn signals on trailers in the same breath as markers, because many modern lamps combine both. Two points keep this straight.
First, a side marker is steady-burning. NHTSA interprets FMVSS No. 108 to require auxiliary lamps to be steady-burning, with exceptions only for lamps that supplement flashing required lamps, such as turn signals, per its auxiliary side lamp interpretation. A lamp that flashes for any other reason is likely out of compliance.
Second, a lamp that works as a marker and a side turn signal needs a proper three-wire design: one circuit for the steady marker function and one for the flashing signal, sharing a ground. Wired incorrectly, the marker function drops out when the signal flashes or the lamp stays lit when it should blink. If you are shopping for this, look at a 3-wire chrome side marker, stop and turn lamp, which is made for that job.
The federal table does not require an extra amber side lamp on every trailer, so do not assume a trailer without one is deficient. Check the specific table entry for your vehicle type before adding anything.
The 80-inch width line and Texas
Many of the top search questions are about specific states, and Texas is the most common. Under Transportation Code Sec. 547.352, trucks and trailers at least 80 inches wide must have four side marker lamps (front and rear) and four reflectors (front and rear). Vehicles over 30 feet long also need central markers, and the color rule matches the federal one: amber for front and side, red for the rear.
The practical takeaway: for a typical 102-inch-wide van trailer, the state and federal layouts line up. Four lamps at the corners, central markers once you pass 30 feet. The difference you will most often meet is paperwork and enforcement style, not hardware. Always look up the statute of any state you run in regularly, and for the width rule and how it separates clearance from marker lights, see our guide on clearance vs. marker lights.
Choosing lamps that fit the layout
Once the positions are marked, lamp choice is mostly about mounting style and durability.
| Mounting style | Best for | Watch for |
|---|---|---|
| Small round lamp (2 inch) in a grommet | Van and flatbed side rails, tight spaces | Needs the right grommet and plug, and a clean hole |
| Oval or rectangular surface mount | Tractor and trailer panels | Flat surface and sealed wire entry |
| Pedestal or fender mount | Fenders, flatbeds, utility trailers | Height above 15 inches, 60-inch cap on rear trailer markers |
For tight rails, a 2-inch round lamp with a reflector lens mounts flush in a grommet. For long panels, a 6.5-inch oval marker is easy to see from a distance. On fenders and flatbeds, a double-face pedestal lamp shows both amber and red faces so one part works at either position.
Perspective: what we see on the install bench
Most spacing failures we hear about are not exotic. They are an intermediate lamp that was never added when a trailer was lengthened, a rear marker mounted too low on a bumper, or a lamp that did not seal and fogged out after a season. That is why we build around sealed, leak-proof housings and brighter LEDs that exceed the minimums, rather than lamps that only barely pass on the day they are installed.
Our advice to fleets is to treat the layout as a drawing, not a guess. Mark the positions, measure the heights, and photograph the finished side of every trailer. When a unit is inspected, you want proof that the front, midpoint and rear positions were planned. Our marker light rules guide and DOT lighting inspection checklist are written for exactly that routine.
— All
Install and inspection checklist
Use this order when adding or replacing side markers.
- Confirm the length. Measure the vehicle. Over 30 feet means an intermediate amber lamp and reflector on each side.
- Mark front and rear positions. Amber at the front end, red at the rear end, as close to each end as the structure allows.
- Find the midpoint. Measure between the front and rear lamp centers and halve it.
- Check heights. Centers at least 15 inches above the road. Rear trailer markers no higher than 60 inches.
- Mount to rigid structure. Seal holes, use grommets or gaskets where specified, and route wire away from sharp edges.
- Verify color and function. Switch on running lights, brakes and turn signals and walk around: every marker steady, turn signal circuits flashing only where designed.
- Clean the lenses and reflectors. The NY DMV manual’s walk-around guidance includes confirming lights work and cleaning lights and reflectors.
- Check for confusing extras. Remove or rewire any auxiliary lamp that could be mistaken for the identification cluster or required lighting.
The result is a trailer that passes a roadside walk-around without argument.
Ready to replace or add markers
If your layout calls for new lamps, we stock DOT-compliant LED markers, reflectors, wiring, and grommets for trucks and trailers. Start with the red 3-light identification bar for the rear, or browse lighting, wiring and reflective products to complete the side layout in one order.
FAQ
How many side marker lights does a semi trailer need?
A standard applicable trailer needs four: two amber at the front and two red at the rear, one on each side of each end. Applicable vehicles over 30 feet add two intermediate amber markers, so a long trailer carries six side marker lamps in total, plus the required reflectors.
How far apart should side markers be?
There is no fixed federal distance. The front and rear lamps go as far toward the ends as practicable, and on vehicles over 30 feet the intermediate lamp goes at or near the midpoint between them. The spacing follows from the vehicle’s length.
What color must side marker lights be?
Amber toward the front and red toward the rear. FMVSS No. 108 calls for two amber side marker lamps at the front of a trailer and two red at the rear, and Texas uses the same color logic. Intermediate markers are amber.
How high do side markers need to be mounted?
At least 15 inches above the road, measured to the lamp center. Rear side marker lamps on trailers must also be no more than 60 inches high. The intermediate reflector sits within the same 15 to 60 inch window.
Do side marker lights have to be steady, or can they flash?
They must be steady-burning. The only flashing allowed is from lamps that supplement a required flashing lamp, such as a turn signal. A combination lamp should be wired so the marker stays lit while the signal flashes.
Sources
- 49 CFR 393.11, Lamps and reflective devices (eCFR.io)
- 49 CFR Part 393 (eCFR)
- NHTSA interpretation GF007705
- NHTSA interpretation on auxiliary side lamps, 2025
- New York DMV CDL-10 manual, Section 2
- Texas Transportation Code Sec. 547.352




