Skip to content
Wish lists
Wish lists
Cart
1 item

Keep Truckin’ Blog

Pre-Trip Inspection Lights: A Walkaround Checklist for Truck and Trailer

by Frank A. 25 Oct 2026 0 comments

A pre-trip lights inspection means turning on every lamp from inside the cab, then walking the whole combination to confirm each light works, shows the right color, is mounted securely and is clean enough to be seen. Do it in a fixed order every time. Test the headlamps, turn signals, flashers and brake lights, walk the tractor, then walk the trailer, and write down anything that fails. If a required light is dead, fix it before you leave the yard.

This guide gives you that sequence, the color and reflector rules behind it, the lights drivers miss most, and what to do when something fails.

Allstartruckparts
Make Every Light Count
Find DOT-compliant truck and trailer lighting, wiring, and reflective tape built for demanding conditions.
Browse lighting and safety products

TL;DR

  • Switch on every light from the cab, then walk the full combination and look at each lamp and reflector. Never just assume a light works.
  • Test brake lights, turn signals and four-way flashers separately. A lamp that works in one mode can fail in another.
  • Colors are fixed by regulation: white headlamps, amber front turn signals and identification lamps, red tail and stop lamps.
  • Lighting devices were the number-one violation nationwide in 2023, with around 300,000 violations, and most can be caught on a walkaround.
  • If a required light fails, do not drive until the vehicle is in good working order, and record the defect on your report.

Table of Contents

Why lights deserve their own pass in the pre-trip

Brakes and tires get the attention, but lights are what roadside inspectors see first. According to CCJ’s reporting on roadside inspections, lighting devices were the top violation category in 2023. CVSA roadside inspection specialist Jeremy Disbrow said these are often problems a driver should catch on a pre-trip walkaround.

The rule behind the habit is plain. The FMCSA Motor Carrier Safety Planner says a driver should not drive unless satisfied that the vehicle’s parts and accessories are in good working order. A dead brake light does not meet that standard.

Lights also matter beyond the inspection. A burned-out stop lamp or a dim marker tells the driver behind you nothing, and on a long night haul that is the failure that gets people hurt.

What the regulations expect you to check

The FMCSA’s inspection procedure splits the job between tractor and trailer. On the tractor, check headlamps, turn signals and other required lamps. On the trailer, check tail, stop and turn signals, other required lamps, and any lamps or flags required for projecting loads. The same document has you check the trailer’s external ABS malfunction lamp.

The CVSA Enhanced Commercial Motor Vehicle Inspection Procedure goes into more detail. It has you check headlamps and high beams, turn signals, and clearance and identification lamps for proper color, operation, mounting and visibility. It adds side-marker lamps, plus tail, stop, turn and other required lamps.

For each lamp, ask four questions:

  1. Does it light when commanded?
  2. Is it the right color?
  3. Is it mounted securely, with no cracked lens or loose housing?
  4. Is it clean enough to be seen?

The walkaround sequence, step by step

Pick one route and never change it. A fixed order is what keeps you from skipping the light you always skip.

Six-step tractor and trailer light inspection route

Step 1: In the cab, before you walk anywhere

Set the parking brake, switch on the ignition and turn on the low beams, the high beams, the four-way flashers and the marker and clearance lights. Watch the dash. Michigan’s CDL manual requires that dash indicators for turn signals, four-way flashers, high beams and ABS be checked for operation when the matching lights are activated.

On a combination, the trailer ABS lamp should come on and then go off when you turn the key, according to CDL Help. A lamp that stays lit, or never lights, is worth a closer look. If you want background on what a lit ABS lamp can mean, this trailer ABS warning light guide covers owner manual steps and recall checks.

Step 2: Front of the tractor

Walk to the front with the low beams still on. Confirm both headlamps work on low and high, the lenses are clear, and the amber front turn signals and identification lamps flash or glow as they should. Check that nothing is cracked, loose or full of water. Look at the ground too: the CDL checklist guidance says no leaks should be visible under the engine is not something we can verify here, so use your own judgment and report any leak you see.

A buddy makes this faster. The MSHA best practice card for highway trucks recommends a buddy system for the rear stop lamps, turn signals, emergency flashers, reflectors and clearance and marking lights. Alone, you can still do it by watching reflections in a wall or a parked truck’s trailer, but a second person is the surer test.

Step 3: Side of the tractor

Look at the side-marker lamps and reflectors, then the clearance lights on the cab roof or visor if your tractor has them. Check each for color, a secure mount and a clean lens. Dirt, road film and snow in winter are the most common reasons a working lamp still fails to be seen.

Step 4: Rear of the tractor

Check the rear tractor reflectors and the mud-flap reflectors. The CVSA procedure lists rear tractor and mud-flap reflectors and reflective tape among the items to verify. Make sure the glad-hand area is clear of anything that could snag or chafe the light cord.

Step 5: The full length of the trailer

Walk each side. Check every side-marker lamp and every reflector, and look at the reflective tape along the sides. The same CVSA document says to confirm the tape covers at least 50% of the trailer’s length. Faded, peeling or dirty tape is a common finding, and it is cheap to fix. Our guide to conspicuity tape colors and DOT-C2 explains what an inspector expects to see.

RED 3 LIGHT COMBINATION CLEARANCE ID BAR MARKER 24 LED TRAILER IDENTIFICATION

Step 6: Rear of the trailer

This is where the helper matters most. Have someone step on the brake pedal, then run the left signal, the right signal and the four-way flashers, one at a time. Michigan’s manual says brake, turn signal and four-way flasher functions must be tested separately. Then check the tail lamps, rear clearance and identification lamps, license-plate light, side-marker lamps and reflectors. CVSA’s procedure lists all of these for the rear of the combination.

If the load projects past the trailer, look for the lamps or flags it requires.

If you are testing for your CDL

The lights section of the skills test follows the same logic, and the examiner is listening. Oregon’s manual says the operation of all external lights must be inspected from outside the vehicle, and that the driver is responsible for telling the examiner which lights to inspect while activating them from inside. It also says that omitting a specific light during the inspection results in no credit for it.

So say each light out loud as you check it. If you are preparing for a driving job, this overview of the trucking skills assessment shows what candidates are asked to demonstrate.

Rules differ a little by state test, so use your own state’s CDL manual as the final word on how to phrase your walkaround.

Colors and conditions: what a correct light looks like

Color is easy to get wrong after a replacement. 49 CFR 393.11 specifies white headlamps, amber front turn signals and identification lamps, and red tail and stop lamps, with colors and placements for other lamps and reflectors. It prohibits amber stop or tail lamps.

Light Expected color What to confirm
Headlamps White Low and high beam work, lens clear, mounting secure
Front turn signals Amber Flashes on command, dash indicator responds
Front identification and clearance lamps Amber All lit, lenses intact
Tail and stop lamps Red Both work, brake brighter than tail
Rear turn signals Red or amber Left, right and four-way flashers each tested
Side-marker lamps and reflectors Amber forward, red rearward Present, lit, clean
Rear identification lamps Red All lit, mounted securely

The table above is a working summary of the colors in the regulation. Check the section itself for exact placement rules on your equipment.

Trailers need reflective material as well. The same section requires trailers at least 2,032 mm wide with a GVWR over 4,536 kg, manufactured on or after December 1, 1993 (with some exceptions), to have FMVSS No. 108-compliant sheeting, reflex reflectors, or both. For the placement rules on clearance and marker lamps, see our explainers on marker light rules and clearance versus marker lights.

The lights drivers miss most

CCJ’s reporting points to rear-facing brake and turn-signal lamps and to headlights as commonly missed items. The reason is simple: you cannot see the rear of the trailer from the driver’s seat. A light you cannot see is a light you do not test unless you build the test into your routine.

Here are the usual suspects, based on how the inspection is structured:

  • Rear signals in a single mode. The tail lamp works but the stop function is dead, or one turn signal fails only when the flashers are on.
  • Upper clearance and identification lamps. They sit high and out of your eye line, so a dead one goes unnoticed.
  • The trailer ABS lamp. It is easy to forget because it is not on the dash.
  • License-plate light. It is a required lamp in the CVSA procedure and an easy one to skip.
  • Dirty lenses and tape. The bulb is fine but the light is not visible.

Intermittent failures are the worst. A light that works in the yard and fails on the road is usually a connection or ground problem, not a bulb. Our guides to trailer lights not working and LED dimming issues walk through isolating the fault. For preventive habits, our truck light maintenance article covers confirming voltage before small faults become violations.

When a light fails before you leave

Stop and decide. The Safety Planner’s rule is that you should not drive unless satisfied the vehicle is in good working order. A dead required light fails that test.

Then follow the steps:

  1. Confirm the fault. Check the bulb or LED, the connector, the ground and the fuse. Many trailer failures are a bad ground or a corroded plug rather than the lamp.
  2. Repair or replace it. Use a lamp that is compliant for that position and the correct color.
  3. Retest the whole function. After you fix the brake light, test the turn signals and flashers again.
  4. Record it. If you cannot fix it on the spot, it goes on your report and your carrier needs to know.

The stakes at roadside are real. The FMCSA says that if a vehicle is declared out of service during a roadside inspection, the defects must be corrected before the vehicle can operate again. A ten-minute fix in your yard costs far less than that.

Pre-trip, post-trip and what gets written down

The two inspections work as a loop. Under 49 CFR 396.13, the driver must inspect the vehicle and be satisfied it is safe to operate before driving. If the previous report noted deficiencies, the driver must review it and sign to certify that required repairs were made.

At the end of the day, 49 CFR 396.11 requires a written post-trip report listing any defect that would affect safe operation or cause a breakdown. Lighting devices and reflectors are among the items the report must cover. The carrier then has to certify that repairs were made or were unnecessary before the vehicle is dispatched again.

For your own records, note the date, unit number and which light failed. A short written note protects you if a defect is questioned later.

There is also the annual inspection. The Annual Periodic Vehicle Inspection Report under 49 CFR 396.17 lists headlamps, front turn signals, identification lamps, side marker lamps, stop and tail lamps, and reflectors or reflective tape. The pre-trip is how you stay ready for it. For a general model of a vehicle checkup beyond lights, this vehicle inspection checklist is a handy comparison.

Our perspective: most light failures are build and wiring failures

We sell lighting, wiring, reflective tape and grommets to fleets, owners and installers, so we see what the same failures have in common. A bulb is rarely the real problem. The usual culprits are water getting into a housing, a thin or corroded wire, a poor ground, and a connector that has worked loose.

That is why we build around leak-proof housings, thicker copper wiring and reflectors made to exceed DOT standards. A pre-trip will catch a dead lamp. It cannot fix a light that keeps dying because the housing leaks or the wiring is undersized.

Our advice for fleets is to treat a repeat failure on the same position as a signal to look upstream. Replace the lamp, then check the wire, the plug and the ground. If the same light fails twice, replace the harness section, not the bulb again.

— All

Replacing what the inspection finds

When your walkaround turns up a failed lamp, a cracked lens or tired tape, we stock the replacements. That includes DOT-compliant LED marker and tail lights, identification light bars, clearance ID bar markers, DOT-C2 conspicuity tape, wiring, connectors and grommets. You can browse everything in lighting, wiring and reflective to find the part for your position.

RED 3 LIGHT COMBINATION CLEARANCE ID BAR MARKER 24 LED TRAILER IDENTIFICATION

A simple routine you can run in five minutes

  1. In the cab: ignition on, low beams, high beams, flashers, markers. Watch the dash and the ABS lamp.
  2. Front: headlamps, turn signals, identification lamps.
  3. Tractor side and rear: marker lamps, reflectors, mud-flap reflectors.
  4. Trailer sides: marker lamps, reflectors, tape condition.
  5. Trailer rear: brake, left, right, flashers, tails, plate light, rear identification lamps.
  6. Clean any lens or tape that is dirty.
  7. Log defects and fix them before you move.

Do it in the same order every day and it becomes automatic, which is the point.

FAQ

Are both pre-trip and post-trip inspections required?

Yes, for drivers of commercial vehicles under the FMCSA rules. Before driving, you must confirm the vehicle is safe to operate under 49 CFR 396.13. At the end of the day, a written report listing safety-affecting defects is required under 49 CFR 396.11.

What is the item most often overlooked on a pre-trip light check?

Rear-facing lamps are commonly missed, particularly brake and turn-signal lights, because you cannot see them from the cab. Using a helper or a reflective surface to test them is the fix. High-mounted identification lamps and the trailer ABS lamp are close behind.

Do I have to test lights separately for brake, turn and flashers?

It is the safest practice, and some state CDL manuals require it. Michigan’s manual says brake, turn signal and four-way flasher functions must be tested separately. A fault can show up in one mode and not another.

Can I drive with one light out if it’s minor?

The rule is that you should not drive unless satisfied the vehicle is in good working order. A required lamp that does not work is a defect that can lead to a citation or an out-of-service order. Fix it, or report it to your carrier before you move.

Sources

Sample Image Gallery

SPRING SUMMER LOOKBOOK

Sample Block Quote

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis.

Sample Paragraph Text

Praesent vestibulum congue tellus at fringilla. Curabitur vitae semper sem, eu convallis est. Cras felis nunc commodo eu convallis vitae interdum non nisl. Maecenas ac est sit amet augue pharetra convallis nec danos dui. Cras suscipit quam et turpis eleifend vitae malesuada magna congue. Damus id ullamcorper neque. Sed vitae mi a mi pretium aliquet ac sed elitos. Pellentesque nulla eros accumsan quis justo at tincidunt lobortis deli denimes, suspendisse vestibulum lectus in lectus volutpate.
Prev post
Next post

Leave a comment

Please note, comments need to be approved before they are published.

Thanks for subscribing!

This email has been registered!

Shop the look

Choose options

Edit option
Back In Stock Notification

Choose options

this is just a warning
Login
Your Cart Good Picks!
Free shipping in all us ORders